View 74LVC2G53DP125_3981861.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

1. general description the 74lvc2g53 is a high-performance, low-power, low-voltage, si-gate cmos device that provides superior performance to most advanced cmos compatible ttl families. the 74lvc2g53 provides one analog multiplexer/demultiplexer with a digital select input (s), two independent inputs/outputs (b0 and b1), a common input/output (a) and an active low enable input ( e). when pin e is high, the switch is turned off. the 74lvc2g53 can handle both analog and digital signals. 2. features n wide supply voltage range from 1.65 v to 5.5 v n very low on resistance: u 7.5 w (typical) at v cc = 2.7 v u 6.5 w (typical) at v cc = 3.3 v u 6 w (typical) at v cc =5v n high noise immunity n esd protection: u hbm jesd22-a114-c exceeds 2000 v u mm jesd22-a115-a exceeds 200 v u cdm jesd22-c101-c exceeds 1000 v n cmos low-power consumption n latch-up performance meets requirements of jesd 78 class i n direct interface with ttl levels n control inputs accepts voltages up to 5 v n multiple package options n speci?ed from - 40 c to +85 c and from - 40 c to +125 c 74lvc2g53 2-channel analog multiplexer/demultiplexer rev. 02 31 march 2006 product data sheet
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 2 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 3. quick reference data 4. ordering information 5. marking table 1. quick reference data gnd = 0 v; t r =t f 2.5 ns; minimum and maximum values at t amb = - 40 c to +85 c; typical values at t amb =25 c. symbol parameter conditions min typ max unit t on turn-on time s to a or bn c l = 50 pf; r l = 500 w v cc = 3.3 v 1.8 3.4 5.0 ns v cc = 5.0 v 1.3 2.6 3.8 ns e to a or bn c l = 50 pf; r l = 500 w v cc = 3.3 v 1.2 2.2 3.8 ns v cc = 5.0 v 1.0 1.7 2.6 ns t off turn-off time s to a or bn c l = 50 pf; r l = 500 w v cc = 3.3 v 1.1 4.0 5.4 ns v cc = 5.0 v 1.0 2.9 3.8 ns e to a or bn c l = 50 pf; r l = 500 w v cc = 3.3 v 2.0 3.7 5.0 ns v cc = 5.0 v 1.3 2.9 3.8 ns c i input capacitance - 2.5 - pf c s(off) off-state capacitance - 6.0 - pf c s(on) on-state capacitance - 18 - pf table 2. ordering information type number package temperature range name description version 74lvc2g53dp - 40 c to +125 c tssop8 plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm sot505-2 74lvc2g53dc - 40 c to +125 c vssop8 plastic very thin shrink small outline package; 8 leads; body width 2.3 mm sot765-1 74lvc2g53gt - 40 c to +125 c xson8 plastic extremely thin small outline package; no leads; 8 terminals; body 1 1.95 0.5 mm sot833-1 table 3. marking type number marking code 74lvc2g53dp v53 74lvc2g53dc v53 74lvc2g53gt v53
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 3 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 6. functional diagram 7. pinning information 7.1 pinning fig 1. logic symbol fig 2. logic diagram 001aad386 s a e b0 b1 6 7 2 5 1 001aad387 a b0 s b1 e fig 3. pin con?guration tssop8 and vssop8 fig 4. pin con?guration xson8 74lvc2g53 av cc eb0 gnd b1 gnd s 001aae798 1 2 3 4 6 5 8 7 74lvc2g53 b1 b0 v cc s gnd e a gnd 001aae800 36 27 18 45 transparent top view
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 4 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 7.2 pin description 8. functional description 8.1 function table [1] h = high voltage level; l = low voltage level; x = dont care; z = high-impedance off-state. table 4. pin description symbol pin description a 1 common a output or input e 2 enable input (active low) gnd 3 ground (0 v) gnd 4 ground (0 v) s 5 select input b1 6 independent b1 input or output b0 7 independent b0 input or output v cc 8 supply voltage table 5. function table [1] input channel on s e l l b0 to a or a to b0 h l b1 to a or a to b1 x h z (switch off)
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 5 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 9. limiting values [1] the input and output voltage ratings may be exceeded if the input and output current ratings are observed. [2] for tssop8 package: above 55 c the value of p tot derates linearly with 2.5 mw/k. for vssop8 package: above 110 c the value of p tot derates linearly with 8 mw/k. for xson8 package: above 45 c the value of p tot derates linearly with 2.4 mw/k. 10. recommended operating conditions [1] to avoid drawing v cc current out of terminal a when switch current ?ows in terminal bn, the voltage drop across the bidirectional switch must not exceed 0.4 v. if the switch current ?ows into terminal a, no v cc current will ?ow out of terminal bn. in this case, there is no limit for the voltage drop across the switch. [2] applies to control signal levels. table 6. limiting values in accordance with the absolute maximum rating system (iec 60134). voltages are referenced to gnd (ground = 0 v). symbol parameter conditions min max unit v cc supply voltage - 0.5 +6.5 v v i input voltage [1] - 0.5 +6.5 v i ik input clamping current v i < - 0.5 v or v i >v cc + 0.5 - - 50 ma i sk switch clamping current v i < - 0.5 v or v i >v cc + 0.5 - 50 ma v sw switch voltage enable and disable mode - 0.5 v cc + 0.5 v i sw switch current v sw = - 0.5 v to (v cc + 0.5 v) - 50 ma i cc quiescent supply current - 100 ma i gnd ground current - - 100 ma t stg storage temperature - 65 + 150 c p tot total power dissipation t amb = - 40 c to +125 c [2] - 300 mw table 7. recommended operating conditions symbol parameter conditions min typ max unit v cc supply voltage 1.65 - 5.5 v v i input voltage 0 - 5.5 v v sw switch voltage enable and disable mode [1] 0- v cc v t amb ambient temperature - 40 - +125 c d t/ d v input transition rise and fall rate v cc = 1.65 v to 2.7 v [2] 0 - 20 ns/v v cc = 2.7 v to 5.5 v [2] 0 - 10 ns/v
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 6 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 11. static characteristics table 8. static characteristics at recommended operating conditions; voltages are referenced to gnd (ground 0 v). symbol parameter conditions min typ max unit t amb = - 40 c to +85 c [1] v ih high-state input voltage v cc = 1.65 v to 1.95 v 0.65v cc -- v v cc = 2.3 v to 2.7 v 1.7 - - v v cc = 3 v to 3.6 v 2.0 - - v v cc = 4.5 v to 5.5 v 0.7v cc -- v v il low-state input voltage v cc = 1.65 v to 1.95 v - - 0.35v cc v v cc = 2.3 v to 2.7 v - - 0.7 v v cc = 3 v to 3.6 v - - 0.8 v v cc = 4.5 v to 5.5 v - - 0.3v cc v i li input leakage current on pin s and pin e; v i = 5.5 v or gnd; v cc = 5.5 v - 0.1 2 m a i s(off) off-state leakage current per channel; v sw = gnd and v o =v cc or v sw =v cc and v o = gnd; v cc = 5.5 v; see figure 5 - 0.1 5 m a i s(on) on-state leakage current per channel; v sw = gnd or v cc ;v cc = 5.5 v; see figure 6 - 0.1 5 m a i cc quiescent supply current v i =v cc or gnd; v sw = gnd or v cc ; i o =0a; v cc = 5.5 v - 0.1 10 m a d i cc additional quiescent supply current per input pin; v i =v cc - 0.6 v; v sw = gnd or v cc ; i o = 0 a; v cc = 5.5 v - 5 500 m a c i input capacitance - 2.5 - pf c s(off) off-state capacitance - 6.0 - pf c s(on) on-state capacitance - 18 - pf t amb = - 40 c to +125 c v ih high-state input voltage v cc = 1.65 v to 1.95 v 0.65v cc -- v v cc = 2.3 v to 2.7 v 1.7 - - v v cc = 3 v to 3.6 v 2.0 - - v v cc = 4.5 v to 5.5 v 0.7v cc -- v v il low-state input voltage v cc = 1.65 v to 1.95 v - - 0.35v cc v v cc = 2.3 v to 2.7 v - - 0.7 v v cc = 3 v to 3.6 v - - 0.8 v v cc = 4.5 v to 5.5 v - 0.3v cc v i li input leakage current on pin s and pin e; v i = 5.5 v or gnd; v cc = 5.5 v -- 10 m a i s(off) off-state leakage current per channel; v sw = gnd and v o =v cc or v sw =v cc and v o = gnd; v cc = 5.5 v; see figure 5 -- 20 m a
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 7 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer [1] typical values are measured at t amb =25 c. i s(on) on-state leakage current per channel; v sw = gnd or v cc ;v cc = 5.5 v; see figure 6 -- 20 m a i cc quiescent supply current v i =v cc or gnd; v sw = gnd or v cc ; i o =0a; v cc = 5.5 v --40 m a d i cc additional quiescent supply current per input pin; v i =v cc - 0.6 v; v sw = gnd or v cc ; i o = 0 a; v cc = 5.5 v - - 5000 m a table 8. static characteristics continued at recommended operating conditions; voltages are referenced to gnd (ground 0 v). symbol parameter conditions min typ max unit v sw =v cc or gnd; v o = gnd or v cc . fig 5. test circuit for measuring switch off-state current v sw =v cc or gnd. fig 6. test circuit for measuring switch on-state current v o i sw i sw 001aad390 s a e b0 b1 v cc gnd switch switch 1 1 2 2 v ih v il s v ih v ih e v sw v il or v ih v ih i sw 001aad391 s a e b0 b1 v cc gnd v ih v il s v il v il e v sw v il or v ih v il
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 8 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer table 9. resistance r on at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); see test circuit figure 7 . symbol parameter conditions min typ max unit t amb = - 40 c to +85 c [1] r on(rail) on resistance (rail) v sw = gnd i sw = 4 ma; v cc = 1.65 v to 1.95 v - 8.7 18 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 7.2 16 w i sw = 12 ma; v cc = 2.7 v - 7.0 14 w i sw = 24 ma; v cc = 3 v to 3.6 v - 6.5 12 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 5.9 10 w v sw =v cc i sw = 4 ma; v cc = 1.65 v to 1.95 v - 12 30 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 8.3 20 w i sw = 12 ma; v cc = 2.7 v - 7.8 18 w i sw = 24 ma; v cc = 3 v to 3.6 v - 6.7 15 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 5.2 10 w r on(peak) on resistance (peak) v sw = gnd to v cc i sw = 4 ma; v cc = 1.65 v to 1.95 v - 57 130 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 15 30 w i sw = 12 ma; v cc = 2.7 v - 13 25 w i sw = 24 ma; v cc = 3 v to 3.6 v - 9.0 20 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 6.0 15 w r on(?at) on resistance (?atness) v sw = gnd to v cc ; see figure 9 i sw = 4 ma; v cc = 1.65 v to 1.95 v - 100 - w i sw = 8 ma; v cc = 2.3 v to 2.7 v - 17 - w i sw = 12 ma; v cc = 2.7 v - 10 - w i sw = 24 ma; v cc =3vto3.6v - 5 - w i sw = 32 ma; v cc = 4.5 v to 5.5 v - 3 - w t amb = - 40 c to +125 c r on(rail) on resistance (rail) v sw = gnd i sw = 4 ma; v cc = 1.65 v to 1.95 v - - 27 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - - 24 w i sw = 12 ma; v cc = 2.7 v - - 21 w i sw = 24 ma; v cc = 3 v to 3.6 v - - 18 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - - 15 w v sw =v cc i sw = 4 ma; v cc = 1.65 v to 1.95 v - - 45 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - - 30 w i sw = 12 ma; v cc = 2.7 v - - 27 w i sw = 24 ma; v cc = 3 v to 3.6 v - - 23 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - - 15 w
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 9 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer [1] typical values are measured at t amb =25 c and nominal v cc . r on(peak) on resistance (peak) v sw = gnd to v cc i sw = 4 ma; v cc = 1.65 v to 1.95 v - - 130 w i sw = 8 ma; v cc = 2.3 v to 2.7 v - - 55 w i sw = 12 ma; v cc = 2.7 v - - 35 w i sw = 24 ma; v cc = 3 v to 3.6 v - - 25 w i sw = 32 ma; v cc = 4.5 v to 5.5 v - - 20 w table 9. resistance r on continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); see test circuit figure 7 . symbol parameter conditions min typ max unit r on = v sw / i sw fig 7. test circuit for measuring switch on resistance i sw v sw 001aad392 s a e b0 b1 v cc gnd switch switch 1 1 2 2 v ih v il s v il v il e v sw v il or v ih v il
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 10 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer (1) v cc = 1.8 v (2) v cc = 2.5 v (3) v cc = 2.7 v (4) v cc = 3.3 v (5) v cc = 5.0 v t amb =25 c fig 8. typical switch on resistance as a function of input voltage v sw (v) 05 4 23 1 001aad406 20 10 30 40 r on ( w ) 0 (1) (3) (4) (5) (2)
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 11 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer (1) t amb = 125 c (2) t amb =85 c (3) t amb =25 c (4) t amb = - 40 c (1) t amb = 125 c (2) t amb =85 c (3) t amb =25 c (4) t amb = - 40 c a. v cc = 1.8 v b. v cc = 2.5 v (1) t amb = 125 c (2) t amb =85 c (3) t amb =25 c (4) t amb = - 40 c (1) t amb = 125 c (2) t amb =85 c (3) t amb =25 c (4) t amb = - 40 c c. v cc = 2.7 v d. v cc = 3.3 v fig 9. switch on resistance as a function of switch voltage v sw (v) 05 4 23 1 001aad410 40 20 60 80 r on ( w ) 0 (1) (2) (3) (4) v sw (v) 05 4 23 1 001aad407 8 4 12 16 r on ( w ) 0 (1) (2) (3) (4) v sw (v) 05 4 23 1 001aad408 8 4 12 16 r on ( w ) 0 (1) (2) (3) (4) v sw (v) 05 4 23 1 001aad409 8 4 12 16 r on ( w ) 0 (1) (2) (3) (4)
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 12 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 12. dynamic characteristics table 10. dynamic characteristics at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); test circuit figure 12 . symbol parameter conditions min typ max unit t amb = - 40 c to +85 c [1] t phl high-to-low propagation delay see figure 10 a to bn or bn to a v cc = 1.65 v to 1.95 v - - 2 ns v cc = 2.3 v to 2.7 v - - 1.2 ns v cc = 2.7 v - - 1.0 ns v cc = 3 v to 3.6 v - - 0.8 ns v cc = 4.5 v to 5.5 v - - 0.6 ns t plh low-to-high propagation delay see figure 10 a to bn or bn to a v cc = 1.65 v to 1.95 v - - 2 ns v cc = 2.3 v to 2.7 v - - 1.2 ns v cc = 2.7 v - - 1.0 ns v cc = 3 v to 3.6 v - - 0.8 ns v cc = 4.5 v to 5.5 v - - 0.6 ns t on turn-on time see figure 11 s to a or bn v cc = 1.65 v to 1.95 v 2.6 6.7 10.3 ns v cc = 2.3 v to 2.7 v 1.9 4.1 6.4 ns v cc = 2.7 v 1.9 4.0 5.5 ns v cc = 3 v to 3.6 v 1.8 3.4 5.0 ns v cc = 4.5 v to 5.5 v 1.3 2.6 3.8 ns e to a or bn v cc = 1.65 v to 1.95 v 1.9 4.0 7.3 ns v cc = 2.3 v to 2.7 v 1.4 2.5 4.4 ns v cc = 2.7 v 1.1 2.6 3.9 ns v cc = 3 v to 3.6 v 1.2 2.2 3.8 ns v cc = 4.5 v to 5.5 v 1.0 1.7 2.6 ns t off turn-off time see figure 11 s to a or bn v cc = 1.65 v to 1.95 v 2.1 6.8 10.0 ns v cc = 2.3 v to 2.7 v 1.4 3.7 6.1 ns v cc = 2.7 v 1.4 4.9 6.2 ns v cc = 3 v to 3.6 v 1.1 4.0 5.4 ns v cc = 4.5 v to 5.5 v 1.0 2.9 3.8 ns e to a or bn v cc = 1.65 v to 1.95 v 2.3 5.6 8.6 ns v cc = 2.3 v to 2.7 v 1.2 3.2 4.8 ns v cc = 2.7 v 1.4 4.0 5.2 ns v cc = 3 v to 3.6 v 2.0 3.7 5.0 ns v cc = 4.5 v to 5.5 v 1.3 2.9 3.8 ns
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 13 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer [1] typical values are measured at t amb =25 c and nominal v cc . t amb = - 40 c to +125 c t phl high-to-low propagation delay see figure 10 a to bn or bn to a v cc = 1.65 v to 1.95 v - - 2.5 ns v cc = 2.3 v to 2.7 v - - 1.5 ns v cc = 2.7 v - - 1.25 ns v cc = 3 v to 3.6 v - - 1.0 ns v cc = 4.5 v to 5.5 v - - 0.8 ns t plh low-to-high propagation delay see figure 10 a to bn or bn to a v cc = 1.65 v to 1.95 v - - 2.5 ns v cc = 2.3 v to 2.7 v - - 1.5 ns v cc = 2.7 v - - 1.25 ns v cc = 3 v to 3.6 v - - 1.0 ns v cc = 4.5 v to 5.5 v - - 0.8 ns t on turn-on time see figure 11 s to a or bn v cc = 1.65 v to 1.95 v 2.6 - 12.9 ns v cc = 2.3 v to 2.7 v 1.9 - 8.0 ns v cc = 2.7 v 1.8 - 7.0 ns v cc = 3 v to 3.6 v 1.8 - 6.3 ns v cc = 4.5 v to 5.5 v 1.3 4.8 ns e to a or bn v cc = 1.65 v to 1.95 v 1.9 - 9.2 ns v cc = 2.3 v to 2.7 v 1.4 - 5.5 ns v cc = 2.7 v 1.1 - 4.9 ns v cc = 3 v to 3.6 v 1.2 - 4.8 ns v cc = 4.5 v to 5.5 v 1.0 - 3.3 ns t off turn-off time see figure 11 s to a or bn v cc = 1.65 v to 1.95 v 2.1 - 12.5 ns v cc = 2.3 v to 2.7 v 1.4 - 7.7 ns v cc = 2.7 v 1.4 - 7.8 ns v cc = 3 v to 3.6 v 1.1 - 6.8 ns v cc = 4.5 v to 5.5 v 1.0 4.8 ns e to a or bn v cc = 1.65 v to 1.95 v 2.3 - 11.0 ns v cc = 2.3 v to 2.7 v 1.2 - 6.0 ns v cc = 2.7 v 1.4 - 6.5 ns v cc = 3 v to 3.6 v 2.0 - 6.3 ns v cc = 4.5 v to 5.5 v 1.3 - 4.8 ns table 10. dynamic characteristics continued at recommended operating conditions; voltages are referenced to gnd (ground = 0 v); test circuit figure 12 . symbol parameter conditions min typ max unit
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 14 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 13. waveforms measurement points are given in t ab le 11 . logic levels: v ol and v oh are typical output voltage drop that occur with the output load. fig 10. input (bn or a) to output (a or bn) propagation delays measurement points are given in t ab le 11 . logic levels: v ol and v oh are typical output voltage drop that occur with the output load. fig 11. turn-on and turn-off times table 11. measurement points supply voltage input output v cc v m v m v x v y 1.65 v to 2.7 v 0.5v cc 0.5v cc v ol + 0.15 v v oh - 0.15 v 2.7 v to 5.5 v 0.5v cc 0.5v cc v ol + 0.3 v v oh - 0.3 v t plh t phl v m v m v m v m gnd v i v oh v ol bn or a input a or bn output 001aac361 v m v i gnd v cc v ol v oh gnd s, e input output low to off off to low output high to off off to high v m 001aad393 v m t on t off t on v x v y switch disabled switch enabled switch enabled a, bn a, bn t off
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 15 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 14. additional dynamic characteristics test data is given in t ab le 12 . de?nitions test circuit: r t = termination resistance (should be equal to output impedance z o of the pulse generator). c l = load capacitance (including jig and probe capacitance). r l = load resistance. v ext = external voltage for measuring switching times. fig 12. load circuitry for switching times table 12. test data supply voltage input load v ext v cc v i t r , t f c l r l t plh , t phl t on , t off high to off off to high low to off off to low 1.65 v to 1.95 v v cc 2.0 ns 30 pf 1 k w open gnd 2 v cc 2.3 v to 2.7 v v cc 2.0 ns 30 pf 500 w open gnd 2 v cc 2.7 v v cc 2.5 ns 50 pf 500 w open gnd 2 v cc 3 v to 3.6 v v cc 2.5 ns 50 pf 500 w open gnd 2 v cc 4.5 v to 5.5 v v cc 2.5 ns 50 pf 500 w open gnd 2 v cc v ext v cc v i v o mna616 dut c l r t r l r l pulse generator table 13. additional dynamic characteristics at recommended operating conditions; typical values measured at t amb =25 c. symbol parameter conditions min typ max unit thd total harmonic distortion f i = 600 hz to 20 khz; r l = 600 w ; c l =50pf; v i = 0.5 v (p-p); see figure 13 v cc = 1.65 v - 0.260 - % v cc = 2.3 v - 0.078 - % v cc = 3.0 v - 0.078 - % v cc = 4.5 v - 0.078 - % f (-3db) - 3 db frequency response r l =50 w ; c l = 5 pf; see figure 14 [1] v cc = 1.65 v - 200 - mhz v cc = 2.3 v - 300 - mhz v cc = 3.0 v - 300 - mhz v cc = 4.5 v - 300 - mhz
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 16 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer [1] adjust f i voltage to obtain 0 dbm level at output. increase f i frequency until db meter reads - 3db. [2] adjust f i voltage to obtain 0 dbm level at input. [3] de?nition: q inj = d v o c l . guaranteed by design. a off(ft) off-state feed-through attenuation r l =50 w ; c l = 5 pf; f i = 10 mhz; see figure 15 [2] v cc = 1.65 v - - 42 - db v cc = 2.3 v - - 42 - db v cc = 3.0 v - - 40 - db v cc = 4.5 v - - 40 - db v ct(sw-sw) crosstalk between switches r l =50 w ; c l = 5 pf; f i = 10 mhz; see figure 16 v cc = 1.65 v - - 68 - dbv v cc = 2.3 v - - 70 - dbv v cc = 3.0 v - - 70 - dbv v cc = 4.5 v - - 70 - dbv q inj charge injection c l = 0.1 nf; v gen =0v; r gen =0 w ; f i = 1 mhz; r l =1m w ; see figure 17 [3] v cc = 1.8 v - < 0.003 - pc v cc = 2.5 v - 0.004 - pc v cc = 3.3 v - 0.0045 - pc v cc = 4.5 v - 0.0045 - pc v cc = 5.5 v - 0.0045 - pc fig 13. test circuit for measuring total harmonic distortion table 13. additional dynamic characteristics continued at recommended operating conditions; typical values measured at t amb =25 c. symbol parameter conditions min typ max unit d 001aad394 600 w 10 m f 0.1 m f s a b0 b1 v cc 0.5v cc gnd c l r l switch switch 1 1 2 2 v ih v il s v il v il e f i v il or v ih e v il
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 17 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer fig 14. test circuit for measuring the frequency response when switch is in on-state fig 15. test circuit for measuring feed-through attenuation when switch is in off-state fig 16. test circuit for measuring crosstalk between switches db 001aad395 50 w 0.1 m f s a e b0 b1 v cc 0.5v cc gnd c l r l switch switch 1 1 2 2 v ih v il s v il v il e f i v il or v ih v il db 001aad396 50 w r l 0.1 m f s a e b0 b1 v cc 0.5v cc 0.5v cc gnd c l r l switch switch 1 1 2 2 v ih v il s v ih v ih e f i v il or v ih v ih db 001aad397 50 w 0.1 m f s a e b0 b1 v cc 0.5v cc gnd c l r l 0.5v cc r l v ih v il s 20log10(v b1 /v i ) 20log10(v b0 /v i ) test condition v il v il e f i v il or v ih v il
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 18 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer d v o = output voltage variation r gen = generator resistance v gen = generator voltage fig 17. test circuit for measuring charge injection 001aad398 s a b0 b1 r l c l v cc gnd r gen v gen switch 1 2 logic input (s) v o e v il 001aac478 d v o off on off logic input v o (s)
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 19 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 15. package outline fig 18. package outline sot505-2 (tssop8) unit a 1 a max. a 2 a 3 b p l h e l p wy v ce d (1) e (1) z (1) q references outline version european projection issue date iec jedec jeita mm 0.15 0.00 0.95 0.75 0.38 0.22 0.18 0.08 3.1 2.9 3.1 2.9 0.65 4.1 3.9 0.70 0.35 8 0 0.13 0.1 0.2 0.5 dimensions (mm are the original dimensions) note 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 0.47 0.33 sot505-2 - - - 02-01-16 w m b p d z e 0.25 14 8 5 q a 2 a 1 l p (a 3 ) detail x a l h e e c v m a x a y 2.5 5 mm 0 scale tssop8: plastic thin shrink small outline package; 8 leads; body width 3 mm; lead length 0.5 mm sot505-2 1.1 pin 1 index
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 20 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer fig 19. package outline sot765-1 (vssop8) unit a 1 a max. a 2 a 3 b p l h e l p wy v ce d (1) e (2) z (1) q references outline version european projection issue date iec jedec jeita mm 0.15 0.00 0.85 0.60 0.27 0.17 0.23 0.08 2.1 1.9 2.4 2.2 0.5 3.2 3.0 0.4 0.1 8 0 0.13 0.1 0.2 0.4 dimensions (mm are the original dimensions) notes 1. plastic or metal protrusions of 0.15 mm maximum per side are not included. 2. plastic or metal protrusions of 0.25 mm maximum per side are not included. 0.40 0.15 q 0.21 0.19 sot765-1 mo-187 02-06-07 w m b p d z e 0.12 14 8 5 q a 2 a 1 q l p (a 3 ) detail x a l h e e c v m a x a y 2.5 5 mm 0 scale vssop8: plastic very thin shrink small outline package; 8 leads; body width 2.3 mm sot765-1 1 pin 1 index
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 21 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer fig 20. package outline sot833-1 (xson8) terminal 1 index area references outline version european projection issue date iec jedec jeita sot833-1 - - - mo-252 - - - sot833-1 04-07-22 04-11-09 dimensions (mm are the original dimensions) xson8: plastic extremely thin small outline package; no leads; 8 terminals; body 1 x 1.95 x 0.5 mm d e e 1 e a 1 b l l 1 e 1 e 1 0 1 2 mm scale notes 1. including plating thickness. 2. can be visible in some manufacturing processes. unit mm 0.25 0.17 2.0 1.9 0.35 0.27 a 1 max b e 1.05 0.95 d ee 1 l 0.40 0.32 l 1 0.5 0.6 a (1) max 0.5 0.04 1 8 2 7 3 6 4 5 8 (2) 4 (2) a
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 22 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 16. abbreviations 17. revision history table 14. abbreviations acronym description cmos complementary metal oxide semiconductor ttl transistor-transistor logic hbm human body model esd electrostatic discharge mm machine model cdm charged device model dut device under test table 15. revision history document id release date data sheet status change notice supersedes 74lvc2g53_2 20060331 product data sheet - 74lvc2g53_1 modi?cations: ? added: type number 74lvc2g53dp (tssop8 package) 74lvc2g53_1 20060110 product data sheet - -
74lvc2g53_2 ? koninklijke philips electronics n.v. 2006. all rights reserved. product data sheet rev. 02 31 march 2006 23 of 24 philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer 18. legal information 18.1 data sheet status [1] please consult the most recently issued document before initiating or completing a design. [2] the term short data sheet is explained in section de?nitions. [3] the product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple dev ices. the latest product status information is available on the internet at url http://www .semiconductors .philips .com. 18.2 de?nitions draft the document is a draft version only. the content is still under internal review and subject to formal approval, which may result in modi?cations or additions. philips semiconductors does not give any representations or warranties as to the accuracy or completeness of information included herein and shall have no liability for the consequences of use of such information. short data sheet a short data sheet is an extract from a full data sheet with the same product type number(s) and title. a short data sheet is intended for quick reference only and should not be relied upon to contain detailed and full information. for detailed and full information see the relevant full data sheet, which is available on request via the local philips semiconductors sales of?ce. in case of any inconsistency or con?ict with the short data sheet, the full data sheet shall prevail. 18.3 disclaimers general information in this document is believed to be accurate and reliable. however, philips semiconductors does not give any representations or warranties, expressed or implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information. right to make changes philips semiconductors reserves the right to make changes to information published in this document, including without limitation speci?cations and product descriptions, at any time and without notice. this document supersedes and replaces all information supplied prior to the publication hereof. suitability for use philips semiconductors products are not designed, authorized or warranted to be suitable for use in medical, military, aircraft, space or life support equipment, nor in applications where failure or malfunction of a philips semiconductors product can reasonably be expected to result in personal injury, death or severe property or environmental damage. philips semiconductors accepts no liability for inclusion and/or use of philips semiconductors products in such equipment or applications and therefore such inclusion and/or use is for the customers own risk. applications applications that are described herein for any of these products are for illustrative purposes only. philips semiconductors makes no representation or warranty that such applications will be suitable for the speci?ed use without further testing or modi?cation. limiting values stress above one or more limiting values (as de?ned in the absolute maximum ratings system of iec 60134) may cause permanent damage to the device. limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the characteristics sections of this document is not implied. exposure to limiting values for extended periods may affect device reliability. terms and conditions of sale philips semiconductors products are sold subject to the general terms and conditions of commercial sale, as published at http://www .semiconductors .philips .com/pro? le/ter ms , including those pertaining to warranty, intellectual property rights infringement and limitation of liability, unless explicitly otherwise agreed to in writing by philips semiconductors. in case of any inconsistency or con?ict between information in this document and such terms and conditions, the latter will prevail. no offer to sell or license nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication of any license under any copyrights, patents or other industrial or intellectual property rights. 18.4 trademarks notice: all referenced brands, product names, service names and trademarks are the property of their respective owners. 19. contact information for additional information, please visit: http://www.semiconductors.philips.com for sales of?ce addresses, send an email to: sales.addresses@www.semiconductors.philips.com document status [1] [2] product status [3] de?nition objective [short] data sheet development this document contains data from the objective speci?cation for product development. preliminary [short] data sheet quali?cation this document contains data from the preliminary speci?cation. product [short] data sheet production this document contains the product speci?cation.
philips semiconductors 74lvc2g53 2-channel analog multiplexer/demultiplexer ? koninklijke philips electronics n.v. 2006. all rights reserved. for more information, please visit: http://www.semiconductors.philips.com. for sales office addresses, email to: sales.addresses@www.semiconductors.philips.com. date of release: 31 march 2006 document identifier: 74lvc2g53_2 please be aware that important notices concerning this document and the product(s) described herein, have been included in section legal information. 20. contents 1 general description . . . . . . . . . . . . . . . . . . . . . . 1 2 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 3 quick reference data . . . . . . . . . . . . . . . . . . . . . 2 4 ordering information . . . . . . . . . . . . . . . . . . . . . 2 5 marking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 6 functional diagram . . . . . . . . . . . . . . . . . . . . . . 3 7 pinning information . . . . . . . . . . . . . . . . . . . . . . 3 7.1 pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7.2 pin description . . . . . . . . . . . . . . . . . . . . . . . . . 4 8 functional description . . . . . . . . . . . . . . . . . . . 4 8.1 function table . . . . . . . . . . . . . . . . . . . . . . . . . . 4 9 limiting values. . . . . . . . . . . . . . . . . . . . . . . . . . 5 10 recommended operating conditions. . . . . . . . 5 11 static characteristics. . . . . . . . . . . . . . . . . . . . . 6 12 dynamic characteristics . . . . . . . . . . . . . . . . . 12 13 waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 14 additional dynamic characteristics . . . . . . . . 15 15 package outline . . . . . . . . . . . . . . . . . . . . . . . . 19 16 abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . 22 17 revision history . . . . . . . . . . . . . . . . . . . . . . . . 22 18 legal information. . . . . . . . . . . . . . . . . . . . . . . 23 18.1 data sheet status . . . . . . . . . . . . . . . . . . . . . . 23 18.2 de?nitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 18.3 disclaimers . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 18.4 trademarks . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 19 contact information. . . . . . . . . . . . . . . . . . . . . 23 20 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

▲Up To Search▲

Price & Availability of 74LVC2G53DP125

	To Download 74LVC2G53DP125 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .